Ring-opening polymerization of 2-oxazolines initiated by chloromethyl groups introduced onto carbon black surface

Summary The ring-opening polymerization of 2-oxazolines (OXZs) was found to be initiated by chloromethyl groups introduced onto carbon black surface. The introduction of chloromethyl groups onto the surface was achieved by the reaction of carbon black with 3,3-bischloromethylbenzoyl peroxide in carbon tetrachloride. During the polymerization, poly-OXZs were grafted from carbon black based on the propagation of the polymers from the surface: percentage of grafting increased with an increase of conversion and reached 40–60%. The polymerization was accelerated by the addition of potassium iodide. Poly-OXZ-grafted carbon black produced stable colloidal dispersions in both hydrophobic and hydrophilic solvents.     

Characterization of electrodeposited WO3 films and its application to electrochemical wastewater treatment

WO₃ films have been prepared on to IrO₂-coated Ti substrate by cathodic deposition, and as-deposited and annealed films have been characterized using XRD, TEM, Raman and FT-IR spectroscopy. The as-deposited film consists of nanocrystalline, orthorhombic WO₃·H₂O and this phase transforms to amorphous WO₃ by annealing at 250 °C and to monoclinic WO₃ by annealing at and above 350 °C. The as-deposited and annealed films have been used as anodes for electrochemical decomposition of phenol in aqueous solutions with and without chloride ions. The monoclinic WO₃ anodes prepared by annealing at 350 and 400 °C show relatively high electrochemical activity in the chloride-containing solution. In addition, the anodes possess high chemical and physical stabilities: very low dissolution rate of WO₃ during the electrolysis and good adhesion to the substrate. Thus, WO₃ anodes may be promising materials for anodic oxidation of bio-refractory organics in wastewater, although further improvement of electrochemical activity is needed for more effective decrease in total organic carbons in wastewater.     

Preparation and characterization of TiO2 and polymer nanocomposite films with high refractive index

Novel nanocomposite films of TiO₂ nanoparticles and hydrophobic polymers having polar groups, poly (bisphenol‐A and epichlorohydrin) or copolymer of styrene and maleic anhydride, with high refractive indices, high transparency, no color, solvent‐resistance, good thermal stability, and mechanical properties were prepared by incorporating surface‐modified TiO₂ nanoparticles into polymer matrices. In the process of preparing colloidal solution of TiO₂ nanoparticles, severe aggregation of particles can be reduced by surface modification using carboxylic acids and long‐chain alkyl amines. These TiO₂ nanoparticles dispersed in solvents were found not to aggregate after mixing with polymer solutions. Transparent colorless free‐standing films were obtained by drying a mixture of TiO₂ nanoparticles colloidal solution and polymer solutions in vacuum. Transmission electronic microscopic studies of the films suggest that the TiO₂ nanoparticles of 3–6 nm in diameter were dispersed in polymer matrices while maintaining their original size. Thermogravimetric analysis results indicate that the nanocomposite film has good thermal stability and the weight fraction of observed TiO₂ nanoparticles in the film is in good accordance with that of theoretical calculations. The refractive index of nanocomposite films of TiO₂ and poly(bisphenol‐A and epichlorohydrin) was in the range of 1.58–1.81 at 589 nm, which linearly increased with the content of TiO₂ nanoparticles from 0 to 80 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Grafting of poly(ethylene oxide) onto C60 fullerene using macroazo initiators

In order to improve the solubility of C₆₀ fullerene in conventional solvents, grafting of hydrophilic poly(ethylene oxide) (PEO) by utilizing the radical-trapping nature of C₆₀ fullerene was investigated. Macroazo initiators containing a poly(ethylene oxide) unit, known as Azo-PEO, were prepared at various molecular weights by the reaction of 4,4′-azobis(4-cyanopentanoyl chloride) with poly(ethylene glycol) methyl ether. PEO radicals formed by thermal decomposition of Azo-PEO were successfully trapped by C₆₀ fullerene to give PEO-grafted C₆₀ fullerene. Their structures were confirmed by FT-IR spectroscopy, size exclusion chromatography, UV-vis spectroscopy, and differential scanning calorimetry. When Azo-PEO with low-molecular weight was reacted with C₆₀ fullerene, a bis-adduct, C₆₀-(PEO)₂, and a tetrakis-adduct, C₆₀-(PEO)₄, were formed. In contrast, in reactions with Azo-PEO of higher molecular weight, only the bis-adduct was formed, and no formation of the tetrakis-adduct was observed. The structure of bis-adduct was found to be 1,4-type. The solubility of C₆₀ fullerene in water, THF, methanol, and other conventional organic solvents was remarkably improved by grafting of PEO. In addition, the thermal stability of PEO was dramatically increased by grafting onto C₆₀ fullerene.     

Si-C-O glass-like compound/exfoliated graphite composites for negative electrode of lithium ion battery

Two low molecular weight silicone compounds, a cyclic type having vinyl groups and a chain-type having Si-H bonds, a catalyst for curing, and a catalyst regulator were mixed. The mixture was impregnated into exfoliated graphite (EG) by sorption, and cured in air at 200 °C. By this process cross-linked silicone coatings were formed on graphite flakes. The composites of Si-C-O glass-like compounds and EG were synthesized by heat treatment of this precursor at 1000-1400 °C for 1 h in argon. The composites formed at 1000-1300 °C were amorphous by XRD and had practically the same chemical composition: Si 44-45, C 27-29, O 25-26, H < 0.5, all in mass%. The ²⁹Si MAS-NMR spectra indicated that the compound formed at 1000 °C was mainly composed of siloxane bonds and amorphous silica, whereas in the compound formed at 1300°C, Si-C bonds and amorphous silica were predominant. The insertion/extraction characteristics of lithium ions for the electrode prepared with composite:poly(vinylidene fluoride) = 90:10 mass% were examined in 1 mol L⁻¹ LiClO₄ solution of ethylene carbonate:diethyl carbonate = 50:50 vol%. High, 650-700 mA h g⁻¹, capacities and steady cycle performance at 50 mA g⁻¹ were achieved with the composites formed at 1250-1300 °C. Capacities of the composites formed at 1200 °C and lower were initially higher but decreased with increasing number of cycles. The composites formed at 1350 °C showed good cycle performance but the capacity was about 500 mA h g⁻¹ due to the formation of β-SiC. Except for the first cycle, the capacity-potential characteristics were similar to those of hard carbons and the coulomb efficiency was 95-100%. For all the composites the capacity was larger than that of graphite (372 mA h g⁻¹) in the range of 50-200 mA g⁻¹. Due to the large insertion capacity of the first cycle, the efficiency was low (60-70%) at first. By short-circuiting the working electrode to the lithium foil counter electrode for a certain period, the irreversible capacity of the first cycle was almost eliminated. It indicates that direct doping of lithium ions into composites is a promising way to increase the efficiency of the first cycle.     

Mechanism of electrodeposition of copper from cupric pyrophosphate solutions

Cathodic polarization curves were measured for copper in cupric pyrophosphate solutions of different concentrations and temperatures. A rotating disc electrode was used to eliminate concentration polarization. For all solutions, two potential regions are distinguishable in the polarization curve; one is less negative than a critical potential E_b around ?0.75 V vs sce (Region I) and the other more negative than E_b (Region II). A weak adsorption of pyrophosphate ions and hence some inhibition of the electrodeposition of copper is expected for Region I but there is no adsorption in Region II. The exchange current density i_o for the copper deposition was obtained by extrapolating the Tafel relation observed in Region II to the rest potential corresponding to the equilibrium potential. The following reaction mechanisms are proposed to explain the dependence of i_o on the concentration of Cu(P₂O₇)^6?₂ and P₂O^4?₇ ions.

Apparent activation energies are estimated to be about 11 kcal/mol in both cases.     

Synthesis of novel UV-curable difunctional thiourethane methacrylate and studies on organic–inorganic nanocomposite hard coatings for high refractive index plastic lenses

This study relates to the development of ultraviolet (UV)-curable, organic–inorganic nanocomposite hard coatings for plastic lens substrates, especially for polythiourethane (PTU) and polycarbonate (PC). Novel difunctional thiourethane methacrylate (mercaptoethylsulfide-thiourethane methacrylate: coded MES-TUMA and isophorone diisocyanate-mercaptoethylsulfide-thiourethane methacrylate: coded IPDI-MES-TUMA) was synthesized to enhance the adhesive strength for PTU. On the basis of IR, ¹H NMR, electron spray ionisation-mass spectrometry (ESI-MS) analysis and gel permeation chromatography (GPC), the expected structures were confirmed. These difunctional thiourethane methacrylates were easily mixed with multifunctional urethane acrylate, surface-modified ZrO₂–TiO₂ nanoparticles and photoinitiator in coating formulations. The UV-cured organic–inorganic nanocomposites were very useful as hard coatings for high refractive index plastic lenses such as PTU and PC.     

Effects of pH and temperature on the deposition properties of stannate chemical conversion coatings formed by the potentiostatic technique on AZ91 D magnesium alloy

The effects of pH and temperature of a stannate bath on the quality of stannate chemical conversion coatings formed on AZ91 D magnesium alloy by using the potentiostatic polarization technique at E = −1.1 V were investigated in order to improve uniformity and corrosion protection performance of the coating films. It was found that the uniformity and corrosion resistance of coating films deposited by potentiostatic polarization were closely associated with pH and temperature of the coating bath. The pH and temperature to obtain the best coating film were investigated as a function of corrosion protection performance evaluated by curves of potentiodynamic anodic polarization conducted in borate buffer solution. Scanning electron microscope observation and electrochemical corrosion tests of the stannate-coated samples confirmed significant improvement in uniformity and corrosion resistivity of coating films deposited by the potentiostatic technique by modifying the pH and temperature of the coating bath. It was also found that uniformity and corrosion resistivity of the coating films deposited by the potentiostatic technique were considerably improved compared to those of coatings deposited by the simple immersion method at the best conditions of pH and temperature of the coating bath.     

Characterization of chitosan/citrate and chitosan/acetate films and applications for wound healing

In this work, we aimed to develop a scaffold of chitosan (CS) with a porous sponge structure for an artificial skin. The scaffolds were prepared from both CS/citric and CS/acetic solutions. In addition, the cast films were also prepared from the same solutions to compare some of their properties. They were characterized using WAXD, FTIR, DSC, tensile measurements, and SEM observation. It was found that CS/acetate had low crystallinity but CS/citrate was in an amorphous state, resulting in a large ductility with rubbery softness. Despite the different morphologies of CS/citrate and CS/acetate scaffolds, both scaffolds exhibited the wound healing effect available for tissue engineering. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Reactive carbon black having isocyanate or acyl azide group

Summary Introduction of isocyanate (NCO) group onto carbon black surface was achieved by the treatment of carbon black with toluene-2,4-diisocyanate. In addition, carbon black having acyl azide (CON₃) group, a precursor of NCO group, was prepared by the reaction of COCl or COOCOOC₂H₅ group on carbon black with NaN₃. The CON₃ group on carbon black was relatively stable at below 20°C but readily decomposed to NCO group by heating (Curtius rearrangement). By the reation of NCO group on carbon black with hydroxyl group of polymers, such as polypropylene glycol, polyethylene glycol, and polyvinyl alcohol, these polymers were found to be grafted onto carbon black.